- Intel Celeron N2930 / Atom E3827 SoC Processor
- Embedded Long-life Series, Lifecycle through Q1'2029
- Ultra slim, low-power, thin form factor design (board z-height is 20mm)
- Supports DDR3L-1333 1.35V SODIMM up to 8GB Total
- Built-in Wide Range +9V â€" 36V DC-In
- ECO-design for EuP/ErP

Specification

Jetway NF9M Mini-ITX Motherboard
Processor	Intel® Celeron N2930 SoC, 1.83GHz 2.16GHz Burst, Quad-Core, 7.5W TDP/4.5W SDP Intel® Atom E3827 SoC, 1.75GHz, Dual-Core, 8W TDP, with AES-NI support
Memory	2 x 204-pin SODIMM DDR3L-1333 Single Channel (up to 8 GB)
Graphics	Intel HD Graphics, 313MHz - 854MHz for N2930 Intel HD Graphics, 542MHz - 792MHz for E3827
Audio	Realtek ALC662 2.1 Channel HD Audio with 3W Speaker Amplifier
LAN	1 x Realtek RTL8111G Gigabit Ethernet with Enhanced Surge Protection
Storage	2 x SATA2 3Gb/s Connectors 1 x Full-size mSATA slot
Super IO	FINTEK F81866A
Back Panel Connectors
1 +9V ~ +36V DC-in jack 1 USB 3.0 1 DVI-I 1 COM port (RS232/422/485) 1 RJ45 LAN (10/100/1000) 3 USB 2.0 1 3.5mm Audio Jacks (Line Out)
Onboard I/O Connectors
1 PCI Express x1 Slot 1 Full size mSATA Slot (shares with one SATA) 1 Full size mini PCI-E Slot (R20 version) 2 SATA2 3Gb/s Connectors 1 USB 3.0 Pin Headers for up to 2 additional USB 3.0 Ports 1 USB 2.0 Pin Headers for up to 2 additional USB 2.0 Ports 3 Serial Port Headers (RS232, +5V/+12V) 1 24-bits Dual Channel LVDS connector/Inverter 1 GPIO header 1 Chassis Intrusion header 1 AT/ATX Mode jumper 1 PS/2 Mouse/Keyboard header 1 Parallel header 1 9-pin Audio header 1 2-pin LAN LED header 1 2-pin SPDIF header 1 4-pin SMBUS header 1 Front Panel header 3 Fan headers 1 4-pin Power Output (Male) 1 2-pin +9V ~ +36V Alternate Power connector (Molex 5566-2)
Power Supply for NF9M
External Power Supply â€" the board can be powered with a +9V ~ +36V external power supply though a DC connector on the back panel. The rear +9V ~ +36V VDC jack accepts plugs with an inner diameter (ID) of 2.5 mm and an outer diameter (OD) of 5.5 mm, where the inner contact is +9V ~ +36V and the shell is GND. Internal Power Supply â€" the board can alternatively be powered via the internal +9V ~ +36V DC 1 x 2 power connector, where pin 1 is GND and pin 2 is +9 ~ +36 VDC. Caution: There is no isolation circuitry between the external +9V ~ +36V DC jack and the internal 1 x 2 power connector. It is the system integrator's responsibility to ensure no more than one power supply unit is or can be attached to the board at any time and to ensure the external +9V ~ +36V DC jack is covered if the internal 1 x 2 power connector is to be used.
Market Segments Supported
Digital Signage Panel PC Industrial Automation/Control All-In-One Retail (POS/Kiosk/ATM) Casino Gaming Thin Client
Environment
Operating Temperature : 0 ~ 60°C Storage Temperature : -20 ~ 85°C